test

Qty:

Add to Enquiry Cart

Specification

Schneider VFD Inverter Drive ATV61F Series 0.75-250KW
range of product	Altivar 61
product or component type	Variable speed drive
product specific application	Pumping and ventilation machine
component name	ATV61
motor power kW	110 kW, 3 phases at 690 V
	90 kW, 3 phases at 500 V
motor power hp	125 hp, 3 phases at 575 V
power supply voltage	500…690 V – 15…10 %
supply number of phases	3 phases
line current	113 A for 600 V 3 phases 90 kW / 125 hp
	117 A for 690 V 3 phases 90 kW / 125 hp
	128 A for 500 V 3 phases 90 kW / 125 hp
EMC filter	Level 3 EMC filter
variant	Low voltage drive for medium voltage motors
assembly style	With heat sink
maximum prospective line Isc	22 kA for 3 phases
maximum transient current	163.2 A for 60 s, 3 phases
nominal switching frequency	2.5 kHz
switching frequency	2.5…4.9 kHz adjustable
	2.5…4.9 kHz with derating factor
asynchronous motor control	Flux vector control without sensor, standard
	Voltage/frequency ratio – Energy Saving, quadratic U/f
	Voltage/frequency ratio, 5 points
	Voltage/frequency ratio, 2 points
synchronous motor control profile	Vector control without sensor, standard
communication port protocol	Modbus
	CANopen
type of polarization	No impedance for Modbus
option card	Communication card for APOGEE FLN
	Communication card for BACnet
	Communication card for CC-Link
	Controller inside programmable card
	Communication card for DeviceNet
	Communication card for Ethernet/IP
	Communication card for Fipio
	I/O extension card
	Communication card for Interbus-S
	Communication card for LonWorks
	Communication card for METASYS N2
	Communication card for Modbus Plus
	Communication card for Modbus TCP
	Communication card for Modbus/Uni-Telway
	Multi-pump card
	Communication card for Profibus DP
	Communication card for Profibus DP V1
Complementary
product destination	Asynchronous motors
	Synchronous motors
power supply voltage limits	425…759 V
power supply frequency	50…60 Hz – 5…5 %
power supply frequency limits	47.5…63 Hz
continuous output current	125 A at 2.5 kHz, 575 V – 3 phases
	125 A at 2.5 kHz, 690 V – 3 phases
	136 A at 2.5 kHz, 500 V – 3 phases
output frequency	0.1…500 Hz
speed range	1…100 in open-loop mode, without speed feedback
speed accuracy
torque accuracy	+/- 15 % in open-loop mode, without speed feedback
transient overtorque	130 % of nominal motor torque +/- 10 % for 60 s
braking torque	<= 125 % with braking resistor
	30 % without braking resistor
regulation loop	Frequency PI regulator
motor slip compensation	Adjustable
	Automatic whatever the load
	Not available in voltage/frequency ratio (2 or 5 points)
	Can be suppressed
diagnostic	1 LED (red)drive voltage:
output voltage	<= power supply voltage
electrical isolation	Between power and control terminals
type of cable for mounting in an enclosure	With an IP21 or an IP31 kit: 3 wire(s)IEC cable at 40 °C, copper 70 °C / PVC
	With UL Type 1 kit: 3 wire(s)UL 508 cable at 40 °C, copper 75 °C / PVC
	Without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 70 °C / PVC
	Without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 90 °C / XLPE/EPR
electrical connection	Terminal 2.5 mm² / AWG 14 (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1…LI6, PWR)
	Terminal 2 x 120 mm² / 2 x 250 kcmil (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3)
	Terminal 120 mm² / 250 kcmil (PA, PB)
	Terminal 2 x 120 mm² / 2 x 250 kcmil (PC/-, PA/+)
tightening torque	0.6 N.m (AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1…LI6, PWR)
	24 N.m, 212 lb.in (L1/R, L2/S, L3/T, U/T1, V/T2, W/T3)
	24 N.m, 212 lb.in (PA, PB)
	24 N.m, 212 lb.in (PC/-, PA/+)
supply	Internal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC, +/- 5 %, <10 mA with overload and short-circuit protection
	Internal supply: 24 V DC (21…27 V), <200 mA with overload and short-circuit protection
	External supply: 24 V DC (19…30 V)
analogue input number	2
analogue input type	AI1-/Al1+ bipolar differential voltage: +/- 10 V DC 24 V max, resolution 11 bits + sign
	AI2 software-configurable current: 0…20 mA, impedance: 242 Ohm, resolution 11 bits
	AI2 software-configurable voltage: 0…10 V DC 24 V max, impedance: 30000 Ohm, resolution 11 bits
sampling time	2 ms +/- 0.5 ms (AI1-/Al1+) – analog input
	2 ms +/- 0.5 ms (Al2) – analog input
	2 ms +/- 0.5 ms (AO1) – analog output
	2 ms +/- 0.5 ms (LI1…LI5) – discrete input
	2 ms +/- 0.5 ms (LI6)if configured as logic input – discrete input
absolute accuracy precision	+/- 0.6 % (AI1-/Al1+) for a temperature variation 60 °C
	+/- 0.6 % (AI2) for a temperature variation 60 °C
	+/- 1 % (AO1) for a temperature variation 60 °C
linearity error	+/- 0.15 % of maximum value (AI1-/Al1+)
	+/- 0.15 % of maximum value (AI2)
	+/- 0.2 % (AO1)
analogue output number	1
analogue output type	AO1 software-configurable current, analogue output range 0…20 mA, impedance: 500 Ohm, resolution 10 bits
	AO1 software-configurable voltage, analogue output range 0…10 V DC, impedance: 470 Ohm, resolution 10 bits
	AO1 software-configurable logic output 10 V, 20 mA
discrete output number	2
discrete output type	Configurable relay logic: (R1A, R1B, R1C) NO/NC – 100000 cycles
discrete output type	Configurable relay logic: (R2A, R2B) NO – 100000 cycles
maximum response time	<= 100 ms in STO (Safe Torque Off)
	R1A, R1B, R1C <= 7 ms, tolerance +/- 0.5 ms
	R2A, R2B <= 7 ms, tolerance +/- 0.5 ms
minimum switching current	3 mA at 24 V DC for configurable relay logic
maximum switching current	R1, R2: 2 A at 250 V AC inductive load, cos phi = 0.4 and L/R = 7 ms
	R1, R2: 2 A at 30 V DC inductive load, cos phi = 0.4 and L/R = 7 ms
	R1, R2: 5 A at 250 V AC resistive load, cos phi = 1 and L/R = 0 ms
	R1, R2: 5 A at 30 V DC resistive load, cos phi = 1 and L/R = 0 ms
discrete input number	7
discrete input type	Programmable (LI1…LI5)24 V DC (<= 30 V), with level 1 PLC – 3500 Ohm
	Switch-configurable (LI6)24 V DC (<= 30 V), with level 1 PLC – 3500 Ohm
	Switch-configurable PTC probe (LI6)0…6 probes – 1500 Ohm
	Safety input (PWR)24 V DC (<= 30 V) – 1500 Ohm
discrete input logic	Negative logic (sink) (LI1…LI5), > 16 V (state 0), < 10 V (state 1)
	Positive logic (source) (LI1…LI5), < 5 V (state 0), > 11 V (state 1)
	Negative logic (sink) (LI6)if configured as logic input, > 16 V (state 0), < 10 V (state 1)
	Positive logic (source) (LI6)if configured as logic input, < 5 V (state 0), > 11 V (state 1)
acceleration and deceleration ramps	Automatic adaptation of ramp if braking capacity exceeded, by using resistor
	S, U or customized
	Linear adjustable separately from 0.01 to 9000 s
braking to standstill	By DC injection
protection type	Against exceeding limit speed: drive
	Against input phase loss: drive
	Break on the control circuit: drive
	Input phase breaks: drive
	Line supply overvoltage: drive
	Line supply undervoltage: drive
	Overcurrent between output phases and earth: drive
	Overheating protection: drive
	Overvoltages on the DC bus: drive
	Power removal: drive
	Short-circuit between motor phases: drive
	Thermal protection: drive
	Motor phase break: motor
	Power removal: motor
	Thermal protection: motor
insulation resistance	> 1 mOhm 500 V DC for 1 minute to earth
frequency resolution	Analog input: 0.024/50 Hz
frequency resolution	Display unit: 0.1 Hz
connector type	1 RJ45 (on front face) for Modbus
	1 RJ45 (on terminal) for Modbus
	Male SUB-D 9 on RJ45 for CANopen
physical interface	2-wire RS 485 for Modbus
transmission frame	RTU for Modbus
transmission rate	4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminal
	9600 bps, 19200 bps for Modbus on front face
	20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen
data format	8 bits, 1 stop, even parity for Modbus on front face
data format	8 bits, odd even or no configurable parity for Modbus on terminal
number of addresses	1…127 for CANopen
number of addresses	1…247 for Modbus
method of access	Slave CANopen
marking	CE
operating position	Vertical +/- 10 degree
net weight	116 kg
width	340 mm
height	1190 mm
depth	377 mm